Boat Trailer Parts and Accessories – How to Replace a Boat Trailer Hub

November 7th, 2011

Step by Step video instructions illustrating how to replace a leaky oil filled hub on a boat trailer.

Watch Video

  • Share/Bookmark

Marine Engines Repower – 1988 sea Ray sundancer with dual MerCruiser 4.3 motors

October 28th, 2011

William,

I would question going to the Par Pac on te one engine because you would have one making about 20% more power than the other which would cause a noticeable issue not to mention a different propeller for that one. Are you dead set on the Par Pac or would you want to look at it by replacing the block with the direct replacement longblock and then adding the cooling system to both motors? Let me know if you need any further technical information or help placing your order. In either case I will be glad to assist!

Regards

Andy
 
Performance Product Technologies/IShopBoating
8002 West 6th Street
Stillwater, OK 74074
(405) 533-3812
Fax (775) 257-1769
sales@perfprotech.com
www.perfprotech.com

Subject: Product Lead Question: GM V6 Power Package 4 Barrel Carb (#2537-4vc)

William writes:
I have a 1988 sea Ray sundancer with dual MerCruiser 4.3 motors. One had a leak in the intake and needs replaced. I would like a quote to buy a 4.3 par pac engine with the fresh water cooling kit. Also what would the cost be to add the cooling kit to second motor? Should I replace both motors at the same time to keep everything even?
This customer was last viewing the following page:
http://www.perfprotech.com/store/product/GM-V6-Power-Package-4-Barrel-Carb,24961.aspx

  • Share/Bookmark

2004 SeaRay Mercruiser 3.0L Marine Engine with raw water cooling and wish to convert closed cooling

October 28th, 2011

Dennis,

Yes we do handle the OEM kit from Mercruiser as well. Using the link below you can add your selected product(s) to your shopping cart and the shipping estimator located at the bottom of the shopping cart page will give you a shipping cost based on your specific postal code. Let me know if you need any further technical information or help placing your order. In either case I will be glad to assist!

Link to Closed Cooling Kit
http://tinyurl.com/3gnk7tt
 
Regards

Andy
 
Performance Product Technologies/IShopBoating
8002 West 6th Street
Stillwater, OK 74074
(405) 533-3812
Fax (775) 257-1769
sales@perfprotech.com
www.perfprotech.com

Subject: Product Lead Question: FWC Kit – Engine Mounted, 3.0L “HIGH CAPACITY” (#5344)

robertson writes:
i have a 2004 searay 3.0L with raw water cooling and wish to convert. the mercruiser drawings show the heat exchanger is block mounted at oil pan level below the manifolds. Do you sell that option? i do not believe there is room enough to mount on the front of the engine
This customer was last viewing the following page:
http://www.perfprotech.com/store/product/FWC-Kit-Engine-Mounted-30L-HIGH-Capacity,26010.aspx

  • Share/Bookmark

Mercury unveils new 150 Hp Four Stroke outboard marine engine

October 28th, 2011

“This is the lightest 150-hp 4-stroke in the world,” said Steve Miller, Mercury Marine brand manager for large outboards. “We have the highest displacement, but the lowest weight. There is a saying, ‘There’s no replacement for displacement.’ This is a very low-stressed engine.”

Read More….

  • Share/Bookmark

Department of Energy: E15 causes “severe damage” to marine engines

October 26th, 2011

WASHINGTON – The results from two studies conducted by the National Renewable Energy Laboratory on the effects of E15 on marine engines were released on Friday, showing that the gasoline and ethanol blend can cause issues including drivability, materials compatibility, increased emissions, and long-term durability in outboard, stern drive and inboard engines, according to the release.

Read More…

  • Share/Bookmark